Winegard TV Antenna RP SK01 User Manual

Automatic Multi-Satellite TV Antenna  
Replacement LNB Instructions  
for Models RP-SK01, RP-SK05, RP-SK09, and RP-SK73  
For help, email [email protected] or call 1-800-788-4417  
2452261  
 
3. Carefully slide the LNB out from the feed arm. Disconnect the four  
coax cables from the LNB using a 7/16” wrench.  
Raising the Antenna  
1. Press and hold “POWER” for two seconds to turn on the interface  
box. Wait until the interface box finishes “connecting to antenna.” The  
TRAV’LER® antenna may enter the search routine after ten seconds.  
Pay attention to the pinch points as the antenna raises!  
4. Connect the four coax cables running through the feed arm to the  
replacement LNB. The coax cables can be connected in any order.  
Tighten the cables until fingertight, and then use a 7/16” wrench to  
tighten a quarter turn more.  
2. Wait until the antenna has at least raised to a position in which the feed  
arm is parallel to the roof. Then, press “POWER” and “SELECT” at the  
same time. The antenna should stop moving.  
5. Slide the LNB into the feed arm, and re-install the two screws  
(removed earlier) through the underside of the feed arm and  
replacement LNB. Tighten.  
3. Unplug the interface box. Continue with instructions for your model of  
replacement LNB.  
6. Slide the LNB guard up the feed arm and over the LNB. The front of  
the LNB guard should be ~½in front of the LNB and should not be  
touching the LNB. Install the four bolts through the four holes in the  
LNB guard. Thread a nut onto each bolt, and tighten.  
Model RP-SK01 DISH® 1000 Replacement LNB  
1. Remove and set aside the two screws from the wider end of the  
underside of the integrated adapter.  
Model RP-SK09 DIRECTV SWM Slimline Repl. LNB  
2. Carefully slide the LNB out from  
the integrated adapter. Disconnect  
the three cables from the LNB  
using a 7/16” wrench.  
LNB slid out from  
integrated adapter  
1. Remove and set aside the four  
nuts and bolts holding the LNB  
guard to the feed arm. Then, slide  
the LNB guard down the feed  
arm and toward the reflector.  
Front of  
LNB guard  
3. Connect the three cables running  
through the integrated adapter  
to ports 1–3 (in any order) on the  
replacement LNB. Tighten each  
cable until fingertight, and then use  
a 7/16” wrench to tighten a quarter  
turn more.  
2. Remove and set aside the two  
screws holding the LNB to the  
feed arm.  
Bolts holding  
LNB guard  
to feed arm  
Integrated  
adapter  
Screws removed  
from integrated adapter  
Screws holding  
LNB to feed arm  
3. Carefully slide the LNB out from the  
feed arm. Disconnect the coax cable  
from the LNB using a 7/16” wrench.  
Feed arm  
4. Slide the LNB into the integrated adapter, and re-install the two  
screws (removed earlier) through the integrated adapter and LNB.  
4. Connect the coax cable running through the feed arm to the  
replacement LNB. Tighten the cable until fingertight, and then use a  
7/16” wrench to tighten a quarter turn more.  
Model RP-SK05 DIRECTV® Slimline Repl. LNB  
5. Slide the LNB into the feed arm, and re-install the two screws  
(removed earlier) through the underside of the feed arm and  
replacement LNB. Tighten.  
1. Remove and set aside the four  
Bolts holding  
LNB guard  
to feed arm  
nuts and bolts holding the LNB  
guard to the feed arm. Then, slide  
the LNB guard down the feed arm  
and toward the reflector.  
6. Slide the LNB guard up the feed arm and over the LNB. The front of  
the LNB guard should be ~½in front of the LNB and should not be  
touching the LNB. Install the four bolts through the four holes in the  
LNB guard. Thread a nut onto each bolt, and tighten.  
LNB guard  
2. Remove and set aside the two screws  
holding the LNB to the feed arm.  
Screws holding  
LNB to feed arm  
 

Westell Technologies Modem B90 36R305 User Manual
Westinghouse Indoor Furnishings W 224 User Manual
Whirlpool Air Conditioner CAH12W04 User Manual
Whirlpool Washer Dryer LA52OOXT User Manual
Whynter Refrigerator MRF 310DB User Manual
Wind Crest Ventilation Hood PER36 User Manual
Xantech Stereo Amplifier PA435X User Manual
Xantrex Technology Power Supply M370078 01 II User Manual
Zanussi Clothes Dryer TD 4113 W User Manual
Zanussi Refrigerator ZRT 6646S User Manual