REFRIGERATOR
ZUD 9124 A
INSTRUCTION BOOKLET
2222683-36
Servicing
At the end of the Appliance Life
• This product should be serviced by an authorised
engineer and only genuine spare parts should be
used.
• When disposing of your appliance use an
authorised disposal site.
The symbol
on the product or on its packaging
• Under no circumstances should you attempt to
repair the appliance yourself.Repairs carried out by
inexperienced persons may cause injury or serious
malfunctioning. Contact your local Zanussi Service
Force Centre.
indicates that this product may not be treated as
household waste. Instead it shall be handed over
to the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring
this product is disposed of correctly, you will help
prevent potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. For more detailed
information about recycling of this product, please
contact your local city office, your household waste
disposal service or the shop where you purchased
the product.
• Remove the plug and ensure that any locks or
catches are removed, to prevent young children
being trapped inside.
Contents
Instructions for the User
Instructions for the Installer
Important Safety Instructions . . . . . . . . . . . . . . . .2
Technical Specifications . . . . . . . . . . . . . . . . . . .12
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Setting the temperature . . . . . . . . . . . . . . . . . . . . . .4
Fresh food refrigeration . . . . . . . . . . . . . . . . . . . . . .4
The door shelves . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Door reversal . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Inner door reversal . . . . . . . . . . . . . . . . . . . . . . . . .14
Electrical Connection . . . . . . . . . . . . . . . . . . . . .15
The
-star compartment . . . . . . . . . . . . . . .5
Building-in Instructions . . . . . . . . . . . . . . . . . . . .16
Grid preparation . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Building in the appliance under a worktop . . . . . . .16
Fitting the plinth . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Freezing fresh food . . . . . . . . . . . . . . . . . . . . . . . . .5
Frozen food storage . . . . . . . . . . . . . . . . . . . . . . . . .5
Thawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Making ice cubes . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Normal Operating Sounds . . . . . . . . . . . . . . . . . . . .5
Health and Safety Guidelines . . . . . . . . . . . . . . . .6
Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Maintenance and Cleaning . . . . . . . . . . . . . . . . . .8
Internal cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Periodic cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Changing the light bulb . . . . . . . . . . . . . . . . . . . . . .8
When the appliance is not in use . . . . . . . . . . . . . . .8
Something Not Working? . . . . . . . . . . . . . . . . . . .9
Service and Spare Parts . . . . . . . . . . . . . . . . . . .10
Customer Care Department . . . . . . . . . . . . . . . .10
Guarantee Conditions . . . . . . . . . . . . . . . . . . . . .11
3
Operation
Before use
Meat can only be stored safely in this way for one
or two days at the most.
Remove all securing tapes. Wash inside the
appliance with lukewarm water and bicarbonate of
soda (5 ml to 0.5 litre of water). Do not use soap or
detergent as the smell may linger. Dry thoroughly.
Fruit & vegetables: these should be thoroughly
cleaned and placed in the bottom salad bin.
Butter & cheese: these should be placed in special
airtight containers or wrapped in aluminium foil or
polythene bags to exclude as much air as possible.
Setting the temperature
Milk bottles: these should have a cap and should be
stored in the bottle rack on the door.
The temperature inside the refrigerator is regulated
by a thermostat control knob with 6 temperature
positions and one «OFF» (O) position.
Position 1 = minimum coldness
Position 6 = maximum coldness
Turn the thermostat control knob to the required
position.
The walls of the refrigerator are equipped with
runners so that shelves can be positioned as
desired.
For better use of space, the front half-shelves can lie
over the rear ones (see fig.).
An intermediate position is usually the most suitable,
although the temperature will be affected by:
•
Room temperature
• How often the door is opened
• How much food is stored
• Position of the appliance
In determining the correct temperature control setting
all these factors have to be considered and some
experimentation may be necessary.
When altering the temperature setting, allow 24
hours for the temperature to stablise before making
further changes.
D338
Important
During prolonged periods of abnormally hot
weather, if the thermostat is set on too high a
number, the cooling system may operate
continuously and the fridge cooling plate may
not defrost. Turning the knob to a lower
number will cause the automatic defrosting to
resume.
The door shelves
To permit storage of food packages of various sizes
the half tray can be adjusted in horizontal.
To do this proceed as figure.
If you wish to return to a lower temperature,
turn the thermostat knob to a higher number,
however you should turn the setting lower
occasionally to allow automatic defrosting.
Fresh food refrigeration
To obtain the best performance, do not store warm
food or evaporating liquids in the refrigerator; do
cover or wrap the food, particularly if it has a strong
flavour.
For more thorough cleaning, the top door shelf and
the bottle shelf can be removed by pulling them in
the director of the arrows, then refitting them in
position.
Do not cover the shelves with any protective
material, such as paper, cardboard or plastic, which
could obstruct the air circulation.
To help you use your refrigerator correctly, here are
some more useful hints:
Raw meat (beef, pork, lamb & chicken or poultry):
wrap in polythene bags and place on top of the salad
bin.
4
Thawing
The
-star compartment
Food can be thawed in a number of ways, depending
on the type of food and the size of the packs.
Meat, fish and fruit should be thawed in the
refrigeration compartment and small pieces of meat
can even be cooked while still frozen, but you must
ensure that it is thoroughly cooked through.
Vegetables should be directly immersed in boiling
water; ready-cooked dishes can be placed directly in
the oven in their aluminium wrapping.
This compartment is suitable for freezing fresh food,
for the storage of commercially frozen food and for
ice cube making.
Freezing fresh food
To freeze fresh foods it is not necessary to change
the setting of the thermostat knob.
However, for a quicker freezing operation, turn the
thermostat knob to the coldest setting; but remember
that, in this condition, the refrigerator compartment
temperature might drop below 0°C. If this occurs
reset thermostat knob to a warmer setting.
Only freeze top quality, fresh and thoroughly cleaned
foodstuffs.
Do not allow fresh food to touch food which is
already frozen.
During the freezing process, ensure that the freezer
compartment door remains closed.
A microwave oven is particularly suitable for thawing
any type of frozen or deep-frozen food: follow the
oven instructions, particularly regarding the
placement of aluminium wrapping in the oven.
Making ice cubes
The appliance is provided with a plastic ice cube tray.
Fill the tray 3/4 full to allow the ice to expand and
place it in the
-star compartment. To turn out
the ice cubes simply give the tray a slight twist to
release the cubes.
Frozen food storage
Never try to free an ice tray that is frozen to the
-star compartment using a sharp or
pointed object.
Storing ready-frozen foods is quite straightforward.
The packs can be placed beside each other or on top
of each other.
Important
You are strongly advised to place ready-frozen food
in the compartment as quickly as possible after
purchase and we therefore recommend that you buy
them last. Also ensure that the external packaging is
intact.
Packaging which is swollen or has traces of refrozen
water droplets on the pack could indicate that the
product has not been kept at a suitable temperature
and that it may have lost its original quality.
Partially thawed food must not be refrozen, it must
be consumed within 24 hours.
Do not consume ice-lollies which have just
come out of the
-star compartment.
Their extremely low temperature can cause
frost burns. Do not remove items from the
-star compartment if your hands are
damp/wet, as this could cause skin abrasions
or "frost/freezer burns".
Normal Operating Sounds
You may hear faint gurgling or bubbling sounds when
the refrigerant is pumped through the coils or tubing
at the rear, to the cooling plate.
Never exceed the storage times indicated.
Do not open the
-star compartment door too
often and do not leave open longer than necessary.
When the compressor is on, the refrigerant is being
pumped round, and you will hear a whirring sound or
pulsating noise from the compressor.
Important
In the event of a power cut do not open the
A thermostat controls the compressor, and you will
hear a faint ‘click’ when the thermostat cuts in and
out.
door. The food in the
-star
compartment will not be affected if the power
cut is short and if the compartment is full.
Should the food begin to thaw, it must be
consumed quickly and must not be re-frozen.
5
Health and Safety Guidelines
Because of consumer demand, preservatives have been removed from many pre-prepared foods.
This together with the changes in shopping habits to a once-a-week shop, mean that safe handling and
storage of food is even more important than ever.
The following tips should help you to ensure that
the food in your home is in as perfect condition
as possible.
• Do not store food uncovered.
• Remove suspect food from your refrigerator and
clean the interior (see “Maintenance and
Cleaning”).
• Keep the time between buying chilled food and
placing it in your fridge as short as possible. Tests
showed that the temperature of 1 litre of orange
juice rose to 22°C in an hour between the
supermarket and home. It then took 11 hours to get
down to 7°C in the refrigerator.
• Never allow spillages to dry and harden.
• Store eggs in the egg rack provided in the
refrigerator door. Discard any broken or chipped
eggs.
• Regularly check the refrigerator door seal to
ensure that it is clean and free from debris.
• Keep the refrigerator door closed as much as
possible.
• Always wash your hands with soapy water and dry
them with a clean towel before handling food.
• Do not push food together too much, try to allow air
to circulate around each item.
• Keep work surfaces clean and avoid cross
contamination by not using the same work surface
or knife, without washing them thoroughly in
between.
• Cool cooked food as quickly as possible but do
NOT place in the refrigerator until cool. (Leave food
in a cool place in order that it can then be placed in
the refrigerator as soon as possible).
• Do NOT mix raw and cooked meat, they must be in
separate containers. Take care not to let the meat
juices drip onto other food. If the meat does drip,
remove everything and clean thoroughly.
6
Defrosting
The refrigerator automatically defrosts every time the
compressor stops. The water is discharged, via the
pipe, into a tray located below the appliance, where it
evaporates.
The freezer compartment, however, will become
progressively covered with frost. This should be
removed with the special plastic scraper provided,
whenever the thickness of the frost exceeds 4 mm.
During this operation it is not necessary to switch off
the power supply or to remove the foodstuffs.
Important
To avoid defrost water overflowing and
dripping onto the food in the fridge, periodically
clean the water discharge hole (F) situated
under the salad drawers. Use the special
cleaner provided (P) which you will find
already inserted into the discharge hole.
Never use sharp metal tools to scrape off
frost from the evaporator as you could
damage it.
Do not use a mechanical device or any artificial
means to speed up the thawing process other than
those recommended by the manufacturer.
However, when the ice becomes very thick on the
inner liner, complete defrosting should be carried out
as follows:
1. pull out the plug from the wall socket or turn the
thermostat knob to the «O» setting;
2. remove any stored food, wrap it in several layers
of newspaper and put it in a cool place;
P
F
3. leave the door open, place a basin on the top shelf
of the refrigerator compartment, under the drain
hole, remove the plug as shown in the figure;
S.I.011
PR151
4. when defrosting is completed, dry the interior
thoroughly and refit the plug.
Keep the scraper for future use; turn the thermostat
knob back to the required setting or replace the plug
in the power socket. After two or three hours, reload
the previously removed food into the compartment.
Important
A temperature rise of the frozen food packs,
during defrosting, may shorten their safe
storage life.
7
Maintenance and Cleaning
Warning
Changing the light bulb
Before any maintenance or cleaning work
is carried out, DISCONNECT the appliance
from the ELECTRICITY supply.
Should the interior light fail to work, first switch off the
appliance and disconnect from the electricity supply,
then replace the bulb as follows:
1. Unscrew the light cover and then pull it outward by
pressing as shown in the figure. Unscrew the bulb
and replace it with a new 15 watt bulb (available
from your nearest Service Force centre).
Important
This appliance contains hydrocarbons in
its cooling unit maintenance and
recharging must therefore only be carried
out by authorised technicians.
2. Replace the light cover by sliding it into its original
position and replacing the screw.
Internal cleaning
Clean the inside and accessories with warm water
and bicarbonate of soda (5ml to 0.5 litre of water).
Rinse and dry thoroughly.
NEVER USE DETERGENTS, ABRASIVE
POWDERS, HIGHLY PERFUMED CLEANING
PRODUCTS OR WAX POLISHES, TO CLEAN THE
INTERIOR AS THESE WILL DAMAGE THE
SURFACE AND LEAVE A STRONG SMELL.
Clean the drain hole of the water trough at regular
intervals and make sure that the drain hole is never
obstructed, so that the defrost water may flow freely.
D411
Important
Do not use abrasive products.
When the appliance is not in use
When the appliance is not in use for long periods,
disconnect from the electricity supply, empty all foods
and clean the appliance, leaving the door ajar to
prevent unpleasant smells.
Periodic cleaning
The appliance is equipped with a ventilation grid.
Keep clean to guarantee good ventilation and good
working order of the appliance.
An accumulation of dust will affect the performance
of the appliance and cause excessive electricity
consumption.
The structure of the appliance permits cleaning of the
rear zone close to the wall, using a vacuum cleaner.
1. Remove the plinth (1), then the ventilation grid (2);
2. Carefully pull the air deflector out (3), checking
that there is no water left from the defrosting.
3
2
1
S.I.013
8
Something not Working?
Before contacting your local Service Force Centre check the following points.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation, a charge will be made even if the appliance is under guarantee.
Symptom
Solution
No power to appliance
- Check there is power at the socket.
- Check there is not a power cut by checking the
household lights.
- Check the fuse has not blown.
The light does not come on
- Ensure that the bulb is correctly fitted.
- Replace the bulb if it has blown.
- Check the door light switch is not jammed.
The temperature in the fridge or freezer section is too - Check the ambient temperature is within the appliances
high
operating limits of 10ÞC to 38ÞC.
- Check the thermostat control knob is turned to the
correct setting relative to ambient conditions.
The compressor runs continuosly
- Adjust the thermostat control knob to give correct
temperature control. See page 4.
- Check that the door is closed.
- Large quantities of food have recently been placed in
the cabinet and/or door is frequently opened.
- Check that air ventilation is not obstructed.
Excessive frost and ice has built up
- Ensure the door is not left open.
- Check that nothing is preventing the door from closing.
- Is the door gasket intact and clean.
Noise
- Refer to normal operating sounds.
Water under the salad bins
- Check the drain hole is not blocked. (see Maintenance
and Cleaning).
If after the above checks, there is still a fault, call your local Service Force Centre.
In-guarantee customers should ensure that the above checks have been made as the engineer will make a
charge if the fault is not a mechanical or electrical breakdown.
Please note that proof of purchase is required for any in-guarantee service calls.
9
Service and Spare Parts
In the event of your appliance requiring service, or if
you wish to purchase spare parts, please contact
your local Service Force Centre by telephoning:-
For Customer Service in Ireland please contact us at
the address below:
Zanussi
08705 929929
Electrolux Group (Irl) Ltd
Long Mile Road
Dublin 12
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
Republic of Ireland
Tel: + 353 1 4090751
For the address of your local Service Force Centre
and further information about Service Force, please
visit the website at www.serviceforce.co.uk
Email: [email protected]
Before calling out an engineer, please ensure you
have read the details under the heading “Something
Not Working.”
When you contact the Service Force Centre you will
need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance
(found on the rating plate)
5. The purchase date
Please note that a valid purchase receipt or
guarantee documentation is required for in-
guarantee service calls.
Customer Care Department
For general enquiries concerning your Zanussi
appliance or for further information on Zanussi
products, please contact our Customer Care
Department by letter or telephone at the address
below or visit our website at www.zanussi.co.uk
Customer Care Department
Zanussi
Addington Way
Luton
Bedfordshire
LU4 9QQ
Tel: 08705 727 727 ( * )
* calls to this number may be recorded for training
purposes.
10
Guarantee Conditions
Standard guarantee conditions
We, Zanussi, undertake that if within 24 months of the date of purchase this Zanussi appliance or any part
thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair
or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
• The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
• The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's
instructions.
• The appliance has not been serviced, maintained repaired, taken apart or tampered with by any person not
authorised by us.
• All service work under this guarantee must be undertaken by a Service Force Centre.
• Any appliance or defective part replaced shall become the Company's property.
• This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
• Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic.
• Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside
the United Kingdom.
• Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
• Products of Zanussi manufacture which are not marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
• The guarantee starts from the date you first purchased your product.
• The guarantee is for the same period and to the same extent for labour and parts as exists in the new
country of use for this brand or range of products.
• This guarantee relates to you and cannot be transferred to another user.
• Your new home is within European Community (EC) or European Free Trade Area.
• The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
• The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service Organisation is aware of your move and able to look
after you and your appliance.
France
Germany
Italy
Senlis
+33 (0) 3 44 62 29 29
+49 (0) 800 234 7378
+39 (0) 0434 39 4700
+46 (0) 8 672 53 90
+44 (0) 8705 727727
+353 (0) 1 4090751
Nürnberg
Pordenone
Stockholm
Luton
Sweden
UK
Ireland
Dublin
11
Technical Specifications
DIMENSIONS
Height
Width
Depth
81,5
59,6
54
cm
cm
cm
POWER SUPPLY VOLTAGE AND FREQUENCY
TOTAL POWER ABSORBED
220-240 V / 50 Hz
80 W
AVERAGE DAILY UNITS ELECTRICITY(*)
0,58 kWh
TOTAL GROSS CAPACITY
122 l
NET CAPACITY
NET CAPACITY
Fridge
102 l
17 l
compartment
STAR RATING
(*) This figure is based on standard test results in accordance with European Standard EN153. Actual
consumption will depend on how the appliance is used and where it is located.
Installation
For building-in and door reversal instructions please
refer to the relevant instructions on the following
pages.
Warning
IF YOU ARE DISCARDING AN OLD
APPLIANCE THAT HAS A LOCK OR CATCH
ON THE DOOR, YOU MUST ENSURE THAT
IT IS MADE UNUSABLE TO PREVENT
YOUNG CHILDREN BEING TRAPPED
INSIDE.
Important
It must be possible to disconnect the appliance
from the mains power supply; the plug must
therefore be easily accessible after installation.
Depending upon the position which you choose for
your appliance, you may wish to reverse the way in
which the door opens. To do this, refer to instructions
under “Door reversal”.
Positioning
The appliance should only be installed at a location
where the ambient temperature corresponds to the
climate classification indicated on the rating plate,
which is located on the inside right of the appliance.
The following table shows which ambient
temperature is correct for each climate classification.
SN
ST
+10°C to +32°C
+18°C to +38°C
The appliance should be located in
a
dry
atmosphere, out of direct sunlight and away from
continuous heat and extreme temperature, e.g. not
next to a boiler or radiator or in a very cold room e.g.
an outhouse. If these temperatures are exceeded i.e.
warmer or colder, then the appliance may not
operate correctly.
12
Door reversal
To reverse the opening direction of the door, proceed
as shown in the figures:
6
4
6
1
7
8
5
6
2
3
1
2
Attention
6
10
After completion of the door reversing
operation, check that the door gasket adheres
to the cabinet. If the ambient temperature is
cold (i.e. in Winter), the gasket may not fit
perfectly to the cabinet. In that case, wait for the
natural fitting of the gasket or accelerate this
process by heating up the part involved with a
normal hairdryer on a low setting.
13
9
6
12
11
3
13
Inner door reversal
1
2
3
180°
4
5
14
Electrical Connection
If you fit your own plug, the colours of the wires in the
mains lead of your appliance, may not correspond
with the markings identifying the terminals in your
plug, proceed as follows:
WARNING
THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability
should this safety measure not be
observed.
Connect the Green and the Yellow (earth) wire to the
terminal in the plug which is marked with the letter
If the plug that is fitted to your appliance is not
suitable for your socket outlet, it must be cut off and
the appropriate plug fitted.
«E» or the earth symbol
yellow.
, or coloured green and
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter «N» or coloured
black.
Remove the fuse from the cut off plug.
The cut off plug should then be disposed of to
prevent the hazard of shocks in case it should be
plugged into a 13amp socket in another part of your
home.
Connect the brown (live) wire to the terminal in the
plug which is marked with the letter «L» or coloured
red.
Important
The plug moulded onto the lead incorporates a fuse.
For replacement, use a 13amp BS1362 fuse. Only
ASTA or BSI approved fuses should be used.
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow - Earth
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured
insert at the base of the plug.
Blue
- Neutral
- Live
Brown
GREEN & YELLOW
13 AMP. FUSE
This appliance complies with the following E.E.C.
Directive:
-73/23 EEC of 19.2.73 (Low Voltage
Directive) and subsequent amendments.
- 87/308 of 2.6.87 (Radio Interference
Suppression) and subsequent amendments.
- 89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
amendments.
BROWN
BLUE
CORD CLAMP
D207
Please ensure that when the appliance is
installed it is easily accessible for the engineer in
the event of breakdown.
15
Building-in instructions
Before carrying out any work, remove the plug from
the power socket.
Building in the appliance under a
worktop
The dimensions of the recessed installation area
must correspond with those indicated in the figure.
Grid preparation
Left door opening:
Remove the left side (A) of the grid cutting it from the
rear (see figure).
A
B
DO013
Installation kit
DO002/2
1xB
2xC
Right door opening:
Remove the right side (B) of the grid cutting it from
the rear (see figure).
1xA
To position the grid on the appliance proceed as
follows:
1xK
Apply the grid to the base of the appliance by
pushing on to the clasps (a) until they click.
18xI
1
a
1. Two cabinet securing brackets are supplied with
the installation pack. They need to be assembled
onto the cabinet prior to cabinet being pushed into
the Kitchen aperture.
a
- To fit these brackets remove the two screws at the
top left and right hand front corners of the cabinet.
DO001
- Position the two brackets as shown in the figure
and replace the two securing screws.
Left hand bracket
Right hand bracket
2
16
2. Push the appliance into place. The plug socket
necessary for connection of the appliance to the
electricity supply should be positioned, so that the
plug is not placed in the recess.
4. The joint cover (B) is to be assembled after having
installed the appliance in the recess.
3. To adjust the height proceed as follows:
- Loosen or tighten the two front feet.
- The rear feet are adjusted by turning the screw in
the front kick plate to the left or right.
1
B
4
+
5. Screw appliance into place and retain the cabinet
with screws (I) through the securing brackets into
the worktop or adjacent woodwork as necessary.
-
-
+
E
3
If necessary, pads (E) are supplied for the rear feet to
make sliding the appliance in and out of the recess
easier. To fit the pads, press them onto the rear feet.
If required, the dimensions of these pads can be
reduced by breaking them where marked.
I
5
6. To mount the furniture door proceed as shown in
the figures:
E
II52
2
1
a
1
0
C
4
3
b
6
17
I
F
27,5 cm
55 cm
27,5 cm
10
7
1
2
45°
a
b
c
3
C
click
11
click
8
1
Upper part of kitchen
furniturepanel
a
I
=
=
=
2
=
10
12
c
b
9
18
Fitting the plinth
Important
For the efficient operation of the appliance, it is
important that the original ventilation grid is
used.
8 mm
F
• For an opening height dimension A=820 mm and a
plinth height dimension a=100 mm, the plinth may
be fitted without adjustments. The same applies to
an opening height dimension B=870 mm and a
plinth height dimension b=150 mm.
I
K
• For plinth heights greater than a=100 mm, b=150
mm, a cut should be made in the plinth, 580 mm
wide, in the centre of the appliance position,
leaving a remaining height of a=100 mm, b=150
mm.
G
• Attach plinth to the kitchen units.
13
7. Refit the covering strip (A).
A
25
DO008
Important
The plinth must be positioned at a minimun
distance of 25 mm from the door.
14
L
90°
115°
L
15
19
© Electrolux plc 2006
|